i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Cannot connect to nRF52840DK board using nRF Connect Bluetooth Low Energy app on Linux (Ubuntu 18.04 LTS). When I choose "Select Device" and choose my board, I get:
"Validating...
We have custom developed board using nrf52832. When I run the example program developed in SDK15.0.0 with Soft device S132 V6.1.1, no issue noticed in running debug mode ...
For creating a Bluetooth mesh Hub that will communicate to the Azure IoT server, which should be the best suitable ethernet board for connecting with the nRF 52 DK?
This is a bug report for SDK v15.3.
Once a GPIOTE interrupt is enabled for a pin, nrfx_gpiote_in_event_enable(pin, false) will not disable it. This appears to be an issue...
Hi,
I wanted to design a custom development board based on nRF52832 SoC. I will go with the exact schematic diagram which was given in Nordic supporting site ( https:...
I'm looking for some additional information about the Assisted GPS functionality in the nRF91.
Exactly what is it?
How does it work?
Is it available with the current...
Hi,
I have an application that does HTTP requests to a backend server. I'm now working on implementing TLS for encryption of the data.
Are there any examples of doing...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
Hi,
I've been searching for a LSM9DS1 driver compatible with the nRF5 SDK >= 14.0 but I couldn't find any which uses the nrf_drv_twi so I started to write my own but it...
Hi All,
I'm working on minimizing power when transmitting a small message between two nRF52832 boards. I'm also trying to maximize range so sensitivity is important.
I...
Please ignore, this is test post. The SES project in Thingy:52 SDK seems to be broken, I get a lot of error trying to compile. What can I do to fix it?
Hello,
I have an application that requires an always running ADC to sample three channels at 4096 Hz. I have successfully adapted my application from the many examples posted...
I am working on Flashing Code into Nordic nRF52832 using SWD Protocol.
We have achieved 80% SWD in communicating and flashed code into Nordic and verified all is working...
I would like to confirm what I'm seeing on my setup trying to measure current with the nRF9160 DK.
I'm using an oscilloscope and am following the instructions in the latest...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
