We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi, I am going to use the nRF91 DK to program an external PCB with the nRF9160 on it. The DK documentation says that only 1.8V or 3.0V is supported for external debug/programming...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
Dear,
I am using nRF9160 DK,
firmware: secure_boot & AT_client
and Tale_SIM from Telia, I want to get the current GPS position by AT command?
Is it possible? Which...
Hi,
In a design which should be compatible with the NRF52832 we want to use the NRF52840. As the NRF52832 doesn't have USB, this would mean that the VBUS and data lines...
I am confused because i see documents referring to cmake/ninja and west. Recently it looks like people are suggesting to use west with master branches. Can someone definitively...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10 .My testing master device is cell phone(Huawei HTC and so on,android system),and using...
Hi
nrF52840 SoftDevice S140 - What is the max ATT_MTU size supported? 244 bytes?
Is there any allowed number of packets per connection event that can be transferred on...
Hey, I just got this nrf52 board with pca10040 and tested few Nordic's examples, which worked just fine. I want to simply put some sine wave signal to one analog input and...
Hello all,
I'm working on a device using nRF52832, interfacing to another microcontroller. I was seeing higher than expected consumption, so started to reduce code to find...
Hi
I just downloaded the nRF connect v2.6.0 - Programmer, but i don't what i have to do to start writing the code.
I only get 2 ``Boxes``, and one of them is called File...
