Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hi there,
I am new to the platform , we are working on a proof of concept to reduce idle power consumption as low as possible on an NRF9160, I want to put the system in...
Hey,
We have a library (rust) responcible for communicating with the BLE peripheral Using btmgmt dbus messages to bluez.
We have never initiated a dedicated `aagent` in...
Hello,
I have a BLE device with the nRF Desktop application, and I want to turn off my device if it is not used, even if it is connected to my PC. I set my CONFIG_CAF_POWER_MANAGER_TIMEOUT...
Good evening,
I have been working for a while on a project that requires the maximum possible speed from both app core and SPIM4 peripheral. To do so, I set the app core...
What is the lowest power consumption method of generating a square wave, less than 100 kHz, and with a differential (or complementary) o/p?
Is it better to use PWM or driving...
usb HID mouse for the home version of the window compatibility is somewhat poor, in the professional version is much better, in the home version often usb does not recognize...
When I download and install NCS2.8.0 SDK, I want to build matter project(ex: light bulb), do I need to install matter build environment referring this link( matter build ...
Hi,
I'm using NCS version 2.7.0 with nrf9151dk. When I tried out the nrf cloud multi service project with hard coded credentials as explained in this document nrf cloud...
Hi Nordic
I had used toolchain manager to download and install previousl ncs versions. Everything was fine.
But, as installing ncs2.9.0, at the end of installation, it...
When I recently tried to write a Gazell project using the nRF Connect SDK, I found that many files referenced the `nrf_gzll.h` file, but I did not find it in the nRF Connect...
Hello everyone!
I'm designing a flexible PCB and I'm a bit confused with the stack up. I've seen that the nRF52840 development board has an NFC antenna with the following...
Hello !
I'm wandering what is this warning when building the sample for the nrf54L15dk :
unit address and first address in 'reg' (0x5004c000) don't match for /soc/peripheral...
I was reading the documentation, trying to figure out something specific while reading though source code. I was looking at the LENGTH field specified in the nrf52840 PS guide...
I'm looking for a correct way to define partitions for my app + mcuboot. Here and there Nordic says that when using MCUboot, the partition manager is used instead of device...
I am experiencing weird radio core boot behavior after switching to SDK v2.9.0-nRF54H20-rc1.
First I followed the bring up guide for SDK v2.8.0, flashed latest BICR for...
