We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
I'm developing a product with the nRF52840, using Zephyr (Toolchain & SDK version 2.7.0). Is there a way to set up two PWM outputs having the same frequency and duty cycle...
Hi,
I am working on implementing an I2C node in my nRF52840 based sensor. However I am getting the following kernel panic.
I removed all I2C node related code that I...
Hi,
I'm developing a new battery powered sensor device with an NRF52840 and have some thoughts about efficient power supply. The main question is: Using an external DC...
Hi,
I have opened Sample "Peripheral_hr_coded" and added build configuration.
Then I clicked on Action --> Build.
Please validate below log. Is it proper ?
Log is...
Is it possible to dynamically switch between USB CDC (Communications Device Class) mode and USB MSC (Mass Storage Class) mode on the nRF52840? If so, could you outline the...
Hi, recently I started migrating my company's firmware from nRF5 SDK to nRF Connect SDK. I have been following the devAcademy courses and so far 1. I have created my custom...
Hello, guys.
We need USB CDC ACM and UART driver with DMA to run in parallel as two different nodes in the device tree.
For that purpose, here is what we have in the prj...
This is a general question about selling our modem-enhanced products internationally. We use an NRF9160 (NB-IoT), but we have some of our devices equipped with older Telit...
Hello,
NAS-RAI (Non-Access Stratum RAI) used on NB-IoT Control Plane : on nRF9160 it was controllable via the AT%XRAI command, using the <rai> parameter :
0 – Undefined...
SOC: NRF52840
SDK : NRF conenct SDK 9.11
Application Gateway
we had end devices to join the network which is whitelisted in the coordinator ; so please can you let...
aliexpress.com/.../1005007557383132.html
I bought the above board I checked the revision information with nrjfprog --deviceversion and it was revision 1 All functions including...
I'm using the nrf52840, and I'm doing a project where the system needs to sleep for a long time, maybe more than 24 hours. Following this ticket, to go to sleep I just do...
Hi
I'm working on understanding how whitelist filtering is implemented and works in Bluetooth Low Energy. I'm currently following Exercise 2 in Lesson 5 of DevAcademy's...
Hi, We are working on power optimization for our project which uses nRF5340 board. Upon testing we observed when starting hardware timer the base level of the current consummed...
My custom board with a NRF5340 (MDBT53-1M) with LF crystal is running as a central on NCS 2.6.1.
It's connecting to a legacy device which has a BLE121LR.
NRF5340 centrals...
