Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
How are the 28-UFBGA pin assignments translated to numbering used to specify I/O pin numbers in the code. Is this as simple as P0.0 => 0, P0.1 => 1,...? I have seen similar...
software:ncs2.5.1
chip:nrf5340
hi professor,
I want to use dtm to test blue RF. After i compile dtm example by vs code and download merge.hex by nrf connect sdk programmer...
Hello,
I am experiencing an issue where ble_nus_data_send returns a value of 0x08. I would appreciate any advice on how to resolve this error.
Symptoms: The device ...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I used UART for communication between...
This is my log output when i connect to my ethernet
this is my prj.conf file
I am building the default AWS_IOT_MQTT SAMPLE. i dont know where i am getting the issue...
I want to implement a network of boards to be placed in a field. We have sender nodes(boards) which will collect data through saadc channels and transmit it to receiver node...
Hello,
i am developing a bootloader with softdevice112 on nrf52805.
I have setup everything and I can see bootloader and app working, just a question about memory layout...
I can't use the I2S api and I2S function in code the compiler says undefined Module , and when i checked the devicetree file there in no definition for the i2s devices
Hello,
I am programming BLE with the nRF52840-DK.
Toolchain Manager: v1.3.0
IDE: Visual Studio Code (VSCode)
SDK: ncs v2.6.0
My implementation goals are as...
With the change from nRF51 to nRF52, the data rate became a minimum of 1 Mbps.
Nordic proprietary radio mode,
nRF51 250 Kbps.
nRF52 1 Mbps,
What is the difference...
Hi everyone,
I working on a project which is a BLE peripheral with Zephyr,
I need to implement the DTM testing for production testing. I created my project base on NUS...
Whenever I respond to a question I opened myself, it generates an "Unread Notification" alert and an email.
I don't need either the website or the email to tell me that...
Hi everyone,
I trying the DTM example and run with debug, I found the software stuck at dtm clock initial. what is the problem , and how can I fixed it , thanks.
...
Hello,
I want to set the transmitting power of the advertising packet. How can I set the TX power?
I am using nRF Connect SDK 2.5.1 in Visual Studio Code.
Regards...
