I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
Im working on a windows 11 Pro (OS Build 22000.1219) with a NRF52 development kit which has a NRF52832 chip set. The board is PCA10040 3.0.0. The device does not communicate...
Hi,
I run the sample zephyr/samples/bluetooth/periodic_adv on 5340, if the controller selected software-base ( CONFIG_BT_LL_SW_SPLIT ), the sample work well; if BT controller...
Hello,
Currently we're working on improving our DALI driver on the nRF52832 chip, because we've experienced issues with transmitting DALI bits with the correct timing. The...
Hello everyone,
I have been trying to get the nRF9160 DK connected to Edge Impulse Platform but it is not possible. i have been following this viedo Connecting nRF9160 DK...
Hello,
I have understood that the pc-ble-driver library is currently in maintenance mode[1] and not getting new features anymore.
We are using pc-ble-driver-py library...
Hello Nordic support,
I am planning to develop an application that will either use Zigbee protocol or BLE protocol. The protocol to be used is determined at startup by reading...
Hi all!
SPI3 Slave project is not built - error:
identifier "__device_dts_ord_DT_N_S_soc_S_peripheral_50000000_S_spi_c000_P_cs_gpios_IDX_0_PH_ORD" not determined
C:\ncs...
Hi,
I want to measure CO2 in different locations using two similar CO2 sensor ( MiCS-VZ-89TE). I can communicate with the sensor over I2C0.
But because two sensors have...
We are facing an issue in nrf52840 (SDK 15). Our hardware uses timer, SPI, USB, FLASH and uDMA. implemented watchdog timer and its working fine as well intented. But in some...
