Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Windows 10
NCS 2.0.0
We have run the Gazell samples successfully on the nRF52833 DKs. In these examples the CONFIG_GZLL_TX_STATISTICS is enabled (gzll_ack_payload_device...
Note: This might actually be a documentation issue more than a real problem because the build seems to work. But some clarification would still be appreciated.
We're developing...
I'm developing FOTA through LTE Modem which is made from QUECTEL(EC21KL)
On my custom board, nRF52832 is connected with EC21 LTE Modem via UART bus(TX : P0.16, RX : P0...
I am updating Nordic Thingy:91. I am following instructions on Nordic's DevZone web page: "Getting NB-IoT Demo running on Thingy:91
I have successfully updated modem using...
Hy
i am using a nrf5349 Dk board ,i am able to build and flash the board.
but when i am using this by building and flashing the board with hci_uart .in the linux system...
Hy ,
After i a buildng and flashing the hci_rpmsg as a cupapp . i flash the board
Then when i am checking the board with ubuntu laptop .i am not able to see the board...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
Hello,
in the nrf connect application for mobile phone I can see the RSSI values being updated when scanning, but when I connect to my peripheral the RSSI info is not available...
Hello, I'm developing firmware for our custom board with a nRF9160.
The problem I'm having is that the modem crashes with error code 0x10 sometimes (read: about every 3rd...
HI guys I am working on nrf connect sdk v2.0.0, I am trying to modify periodic_adv example to stop changing mac address every time an advertising restart.
