I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello everyone,
I am working with the latest Zephyr NCS 2.0.2 SDK to develop a BLE App with a nRF52840 Soc.
The device is going to produce a very low data rate, so I want...
I am using Nordic seriaization with nrf52480 as connectivity chip and a custom M4 board as Application chip. After 5th connection, the advertisement is not starting. While...
Hello team,
I am trying to build an audio LE application where I require a stereo output and microphone input. As an initial part of the project, I am trying to connect...
Hi,
I'm developing firmware for nRF52840 device (Acconeer XM122), and I'm trying to use fstorage library to write some data to flash.
SDK version 15.3.0, Segger Embedded...
I'm currently attempting to get the nRF 9160 to enter PSM mode when not transmitting along with the asset_tracker_v2 application just so we can do some power consumption measurements...
Hi Dev Zone,
We have an existing design that includes the Espressif ESP8266 Wi-Fi MCU and we would like to add an nRF52 to the design. Our preference would be to add the...
I'm using NRF52833 with SDK v16.0.0 along with mesh SDK v4.1.0. I want to know if it's possible to write data which is not word aligned into the internal flash (For example...
Hi everyone,
I started working on nordic nRF52832 DK and tested out some examples. I think i am done with the examples now and am looking to write my own code apart from...
Dear Members,
How can we determine the first ANT message from my transmitter ?
We saw from ant_parameters.h,
Which variable is being used ?
Kind regards...
Hi,
Today I found that after I OTA my board, it runs well at first. But when I reset it, it will run old image again.
Before this OTA, my board has gone through many OTAs...
hi all,
I am currently working on a ble project, the led based on the NRF52832 chip is used as the slave, and the mobile phone is used as the master to form a star network...
I use nRF Connect to connect to nRF52832 device. 1st connection is bonded authenticated encrypted link, but 2nd connection becomes not bonded unencrypted link. Why 1st and...
Hi,
I was provisioning devices for a customer today when I noticed at the end of provisioning that the JSON database file that was exported had all the features except ...
Hello,
We are developing a library which is intended to use the trustzone feature available with nrf5340 DK. We followed the instructions available in Using a custom Secure...
