I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hello,
Can raw data be published via MQTT with SLM 1.7?
In later versions we have done this by entering data mode, which we see is not implemented here.
Is there another...
I'm using the nRF52832 in an energy harvesting application, where I need to cold-start the device and set a GPIO output high in under 50ms in order to latch the power supply...
When using AT command to send data, the baud rate is set to 9600, and the two modules are connected at different temperatures, and the data is sent through the serial debugging...
Hello everyone
The company I work for produces an nRF52840 based dongle.
We also have a bootloader which is a modified sdk example.
We need to save some important data...
I'm trying to install nrf-command-line-tools_10.17.0_amd64.deb on an up to date Debian 11, but dpkg always fails with this error:
# dpkg -i nrf-command-line-tools_10.17...
Hi there,
We appear to be having the same issue as described here and here on a nrf9160 DK. There was no clear changes to hardware at all. LED5 suddenly does not seem to...
Hi Nordic support,
I have been evaluating the nrf5340 audio DK and recently run into a build issue with the example application. I have been able to successfully build...
The following error occurred after BLE APP connects to nRF52832 device. How can debug this issue?
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ..\..\..\..\..\..\components...
Hi.
I'm trying to include MCUboot in my application following this guide but I get this error:
I'm using version 1.8.0 of the nRF Connect SDK with a project using spm...
Hi,
I notice that the Power Profiler II (nRF-PPK2) connectors are polarized. I'd like to make special cables for my test fixture. Can you tell me the manufactures P/N for...
Hello all,
I am using the PWM and TIMER drivers on the nRF52DK board among other drivers like TWI and I get this error when trying to compile, eg. today
It can be seen...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I use MPU6050 for my project. I wanna ask about this code caculating the value of MPU6050 . The function below caculating the value of GYRO of MPU6050.
What is the range...
Hi,
I am a newbie to the world of nRF. I am trying to develop a gateway using nRF52840dk using nRF connect SDKv2.0.0.
While I am trying to create a freestanding application...
