I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Can someone please post a simple example of using the internal oscillator with BLE? Modifying the ble_app_blinky example to use the RC would be ideal. No matter what I do...
Hi support team,
Now i am trying to understand the LPN machenism based on the LPN example. I cannot make sure where the bear handler is started.
There is a function bearer_handler_start...
Hello,
I'm planning to work on a device which should have two nRF5340 modules on a small PCB (they will be max 2cm apart from each other). Both modules will broadcast data...
Greetings,
I am using the NRF53 DK along with the Zephyr/Beacon (nRF Connect SDK v1.91) example for an ultra-low power application. I would like to know how I can change...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
Hi.
In a prototype built for a small group of test users (20-25), we want to implement a simple tactile reset button for use in case of an anomaly (as the prototype software...
Hello,
I am using nRF9160 dev kit in Chicago (USA) and in Aldingen (Germany) where I am using same firmware for both DK to get GPS Fixes for location. But surprisingly in...
good try,
i tried adding buttonless dfu service to ble hid_mouse/keyboard sample in nRF52 SDK 17.1 with PCA10040 dev board but it does not show up in the list of devices...
If the privacy feature is disabled, calling bt_conn_le_create will change the state to BT_CONN_CONNECTING_SCAN (since bt_dev.le.rl_size == 0) and then call bt_le_scan_update...
