Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
Hello Everybody,
If you're reading this, you're likely in the same boat as me and need to scale Nordic's build process in an environment that doesn't have access to west...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
I notice that the fork sdk-zephyr https://github.com/nrfconnect/sdk-zephyr
is missing important errata updates for nRF82510
as it is using and outdated https://github...
Hi, I'm trying to use the pwm driver to turn off or on a dc motor (which the speed will variate via the pwm signal). I need to achieve a frequency between 20kHz and 100kHz...
Hello,
How can I configure for a GATT characteristic which type will be used.
Without defining it will be a byte array.
I'd like to configure for example an int16 number...
Hi,
I am using Win10, nRF Connect 3.9.0, programmer 2.0.0. and I get "no matching trait found" when trying to program the 9160 on my board. I have seen a few other questions...
