Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I am new to NRF chips and trying to read, write, and erase to flash using nrf_fstorage. I have looked at the example project flash_fstorage and I am able to successfully read...
Hi All,
I'm trying to generate an interrupt on the X PWM's falling edge. My idea was to setup the PWM and count the number of falling edges using PPI & a timer / counter...
I have following code fragment to enter nRF52 into power-off mode. There is s132 softdevice 3.0.0 running and my SDK is 12.0.0:
int32_t ret = sd_power_system_off();
...
Hello,
I am having an issue viewing serial communication from the nRF9160 on the LTE link monitor. I am able to view output when the code is compiled from a different...
After burning the application, the following operations were performed: nrfjprog.exe -f NRF52 --rbp ALL nrfjprog.exe -f NRF52 --pinreset
There are a total of 600 devices...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
