hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi, I'm trying to run the Openthread Cli sample on my nrf5340 DK, and it looks like that part is doing fine. But if I want to test the thread network with Putty I don't get...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi,
I'm trying to see how a BLE packet is formatted and sent from a Thingy:52 and I know the preloaded code on the THingy:52 has that functionality, can you direct me to...
Hi, do you have plans to test the nrf52805 at 105 degC or higher, similar to nrf51822 Extended Industrial Temperature range document
We will probably run the NRF52805 at...
I have created zigbee network using nordic dk board, i am trying to fetch all the active nodes in the network using zdo mgmt_lqi cli and i am getting those details but when...
Hi, What is in your opinion the best way to handle device reset after the Zigbee connection fails?
I want to archive behavior like so: after connection fails sleep for 10...
Hello,
I am working on a project which requires 2 FTDs and 2 MTDs (Sensor and Actuator) in a Thread Network.
We are using nRF52840 dongle as FTDs and arduino nano sense...
after connect v3.7.1 programer v1.4.11 for a nrf9160dk I get an error "Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: INVALID_OPERATION...
I have followed the tutorial of nRF5340: Network core bootloader to test the bootloader on app. core & net core.
I chose to use VS code to develop.
I am successful to...
Hi.
Simcom SIM7000 series datasheet recommends the following schematic:
Simcoms SIM800C module datasheet recommends the following schematic:
Quectel BG96 module...
I currently use an NRF52810 to write a firmware in an external flash, then an STM32 will read this firmware and download it in its internal flash. The communication between...
Hello,
I tried to read the value from bq4050 on smbus.
I had good results but I got wrong value randomly as following.
The last marked value is temperature from DAStatus2Reg...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
