Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi,
I'm trying to flash the firmware to some custom built pcb's with NRF52840 on it. The first time I flash it, it works great.
Then, if I try to erase the chip (or any...
Hello
I have this firmware running in C:\Users\danie\ncs\v1.5.1\nrf\applications\tracker on the nRF9160-DK, nRF9160 SICA B1 is the marking on the chip
Modem FW is...
Hi. Some questions regarding the nRF9160 ENABLE pin:
1. According to the nRF9160 product specification the ENABLE pin voltage requirements are like this:
In the first...
Is it possible to add additional UI for different sensors in nrfcloud platform ? I could see that there is a predefined list of sensor types that can be attached to cloud...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. I would like to measure the time required to send a message from client to server...
Hi all,
I'm working on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fthread_example_dfu.html
I'm struggling on the server part, I...
Hello,
we are developing a verry small sensor node. Since we like to know if the sensor we are connected to, is one of our sensors instead of an attacker fake sensor we...
Hi! I was testing GPIOTE with pin_change_int example and tried to add a log to the push of the button.Somehow the code is not working, it is indeed changing the state of the...
nrf52840, sdk17. pca10056 (for now). linux arm-gcc, gnumake, etc.
I have a fairly complex PPI configuration but in the act of debugging it, I've dumbed it down quite a...
How does the interrupt latency compare between COMP/LPCOMP and GPIOTE? Are t LPCANADET and t PROPDLY the correct field to be looking at in the specification? The electrical...
Hi Nordic Team,
My Board: nRF5340 DK; SDK: nRF Connect SDK v1.5.0
I am new to BLE developement. I am trying to design a GATT service which can be accessed by nRF Connect...
I'm trying to use UART flow control and assign RTS CTS pin numbers.
What's the corresponding number for P0.02, P1.15 each?
And where can I find this information?
Hi,
I have used nRF52811 SoC in my custom design. In this circuit i have used SWD interface only as per reference design. I have used same SWD 10 pin connections as mentioned...
128 MHz or 64 MHz operation is mentioned in the specification (page ii). However, can MCU be capped at around 12MHz? How about the current consumption?
I am starting an experimentation effort with Nordic Mesh SDK. I am using Segger Embedded Studio.
I can open/compile/download the Mesh SDK examples.
I wish to start to...
