I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I installed NRF connect SDK v1.5.0-rc1.0 through toolchain manager.Open SES and create a project with open NRF connect SDK project.An error occurred.'create_nordic_project...
This function succeeds only when Thread protocols are disabled. my question is: if the Thread protocols are enable,what should I do to disable them ，now what I do is:
"otThreadSetEnabled...
Hi . I am developing nRF52 for the first time. (PCA10056_ nRF52840 _S140_ ver1.70.0 _DK under development..) It is under development with SEGGER embedded studio. I want to...
I'm new to NCS, and playing it with nrf5340 pdk kit.
My problem is ,I can't play any projects, all of them go to the same error: cmake failed,create_nordic_project.py failed...
Hi,
To support the large and dense networks we are building, I need my network coordinator to be able to throttle OTA packets to not completely overtake the network’s bandwidth...
Hi,
I want to create a mesh between my nRF53 DK and dongle. For my project, I created my own service to send accelerometer value to the client (mobile application). Now...
I am developing an application that sends an image with BLE to an android phone. It is remarkable similar to the Image transfer demo ( https://github.com/NordicPlayground...
Hi
I am updating from Softdevice 6.1.1 to 7.2.0 and have issues with nrf_sdh_ble_enable(..), My setup is:
NRF52840
SDK 17.0.2
SoftDevice 7.2.0
Running FreeRtos...
Hello,
Sorry for this long question but these questions are bothering me and I need these to carry on with my project.
1) What is the peer manager's device identity list...
I want to use nRF52840 USB dongle as mesh server device. I have tried several links but not success. Please provide me hex file so I can flash using nRF connect desktop app...
Is there a way only from the analog input where measure the battery voltage to distinguish that battery is charging?
I am short on IOs and will be quite a challenge to find...
Dear all: Recently, I was debugging nrf52805 by custom PCB, using sdk17.00, I enabled PWM, frequency of 4kHz, to drive 4kHz passive buzzer, encountered a problem: The buzzer...
Hi,
I'm having problem using SPIS on nrf9160. The data/clock from master looks clean on scope, but 91 is not receiving the data. Interestingly, when I connect a debugger...
Dear,
We would like to have a setup where we want to measure the current consumption of a battery-powered device with an NRF-52840 chip:
The battery is a Li-Ion one...
Hello together,
I am try to get the asset_trecker_v2 to work on my thingy 91. When reading the debug log in LTE Link Monitor I see the warning:
So I downloaded the latest...
