I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
With reference to BLE Fundamentals Lesson 4, I am try to modify my existing BLE code to add indication support.
After adding the codes, I can see the "Read and...
We are encountering an issue with flashing firmware to our newly designed nRF54L05 BLE board.
Issue Details:
We are trying to flash a .hex file (simple Blinky code...
Dear Nordic Support,
I am currently performing initial tests for distance measurement using Channel Sounding with the nRF54L15 Development Kit.
Here are the details of...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi Nordic team,
We are interested in using nrf9161 SiP. can you confirm if the `zephyr,nrf91-slm` driver work on the nrf9161? We are interested in the DECT NR+ capability...
Hi i am trying to configure a timer to work in count mode and when it hits a certain number ( for example 100) to activeta an interrupt, clear count and start again.
Best...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Hello!
I am trying to set up automated tests for an application on the nRF54L15 BabbleSim target. The application needs two-way communication with a test script; this would...
hello
In the nrf/sample/net/aws_iot example, when updating a shadow topic, use $aws/things/<thing-name>/shadow/update/
Where does "thing-name" refer to?
Regards,
Dae...
Hi All,
We have an application that was compiled on nrf54L15DK where we get UART logs . The application was tested on DK and is working fine. Use Case:
Wanted to run...
I am interfacing the DS18B20 digital temperature sensor with the nRF52810 using the nRF5 SDK . The same firmware and hardware configuration works correctly on the nRF52832...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
Hello,
I am currently using the bt and uart backend for zephyr logging on ncs 2.9.2. I want to be able to save logs to flash which will be useful in debugging/ and be...
I am trying to establish a BLE connection between two nRF52840 devices.
The child devices are properly advertising and are close to each other.
When attempting a BLE connection...
Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
