I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
Hello I have a problem with the scanning of ble phy coded in Android, I need it to be continuous (or almost) but it seems that for coded it is not possible unlike with legacy...
There are more than one task, after completing the periodic work,the 52832 module should enter system on low power mode,sleep 30 minutes,then wake up and continue with the...
Hello:
I have set the scanning module to search devices by MAC address. It finds the devices that are using a Static Random address, but it cannot find the ones using a...
Hi,
in my project I have a custom board with a nRF52832 chip that reads SAADC data and transmits this data (peripheral role). This data is received by a nRF52840-DK board...
I have an application that is running on using nRF52840 and FreeRTOS. I am considering transitioning to nRF5340. For now, it appears that this also means transitioning from...
Hi,
I am exploring the feasibility of building a firmware for nRF52840 that supports both BLE Mesh as well as ZigBee stack (in the same firmware) but only require one of...
Hello I am using sdk v17.0 and nRF52DK.
I'm going to simply read the analog sensor MICS-5524 (gas sensor). And to do this, we used the SAADC example code and connected it...
I want to write a piece of big data to flash. Every time I write 112 word length, I write it many times. Every time I write, the address is shifted back 112. Before I write...
Hi,
Im using nRF52 DK for my project. I bought this makerdiary nRF52840 dongle as a secondary device. I go through the initial setup, it looks different than a nrf device...
Hi,
I'm using SDK 11.0 and I want to implement a firmware update procedure over GSM. The firmware data packets should be received via UART (which is connected to the GSM...
Hi !
As proof of concept i need to connect BLE keyboard which working as HID pheripheral to my CENTRAL unit.
I write the CENTRAL part ! As far as i searched i didn't find...
