I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Do you know how to handle a write event from its (such as char) descriptor value in a customized BLE service ?
Here is the code of my on_write function :
Setup : nRF52840...
Hello,
I am working with the nrf52832, softdevice s132, and I have configured my own service using this online tutorial :
https://devzone.nordicsemi.com/nordic/short...
hi
im use the command line of nrfutil to ota the nrf52840' firmware.but now i want to develop a soft to ota the device without the environment of python.but i dont kown...
Hello,
I'm measuring the value of a lithium battery (3.7V 110mAh). I used SAADC to measure the battery power and it seems to be quite accurate. The charge IC also attempts...
Hello,
In an older post ( here ) you mentioned that you removed Touchlink examples because they were not of "production quality" and they might not be soon. That was two...
Hi,
Considering https://devzone.nordicsemi.com/f/nordic-q-a/29013/best-way-to-implement-system-clock-on-nrf51 as reference and some other similar posts.I could reach to...
I have created a couple of custom BLE services and characteristics in a peripheral application. It shows up in the nRF Connect app and can read the values from sensors connected...
Hello, we are occasionally getting an error 0x3001 from this function call:
rtn = sd_ble_gap_disconnect(m_ConnectionHandle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE);
I do not...
Hello,
I want to use the code from the BLE template in my own application and so I copied all necessary files into the project, but the code stucks at
I have debugged...
Hi;
I am using nrf mesh sdk 4.2.0 version and nrf sdk 16.0.0 .
I inttegrated UART code to light switch client example code.
Both UART and client code working seperately;but...
Hello, support team.
In my test board, lis3mdl chip is connected to nordic chip via I2C.
During initializing board, device ID of lis3mdl is checked.
Most of time it...
With 900ms advertising interval we are seeing ~50uA sleep current on the 52840. How do we make it sleep with lower current? We are using an example project with an idle_state_handle...
Hi,
What is the procedure to use PCA10056 DK Debug OUT P19 connector to program external board for eg Nordic Thingy 52?
I have shorted SB47 on PCA10056 DK but it is failed...
