Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
I'm trying to flash the asset_tracker application to the nrf9160dk. I use Segger Embedded Studio for building the project for the nrf9160_pca10090ns board. However,...
Hi,
We are using a NRF52840 chip (SDK 15.3) in an application where we use the softdevice (S140) in combination with 2 UARTS: one for sending out debug output (UART0 - nrfx_uart...
Hi, We have a nrf52 which runs some project using ANT, now we would like to implement BLE for UART communication between a phone and the unit. The code base is already extensive...
Hi,
I just connected an nRF91 dk to nRF Cloud, which worked fine. However, for some reason the GPS says I am in Trondheim, while I am clearly somewhere else in the world...
I try to communicate with NRF52832 with NRF51822 for the example radio receiver and works well with SDK5 12 3
when I try to communicate with E73 (NRF52840) board(E73(2G4M08S1C...
How to push Initiator to resolve its private address (seen at direct_addr of adv_report) when bonded private Advertiser does a direct advertising?
I need the only Initiator...
I've followed the procedure on the nRF connect cloud to verify the SIM card and add the LTE device, only once the LED3 and LED4 blink at the same time like it was connected...
We are using a NRF52840 chip (SDK 15.3) in an application and are having issues with the startup of the board. I managed to create an example application where I integrate...
Hi. I have attempted to add an out endpoint to the HID usb generic example (only 1 in endpoint in example as it is a mouse).
However it is not working. When connected my...
Is there any UART examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
Hi, I measure current in beacon in Long Range mode. Behind 3 current peaks witch represent TX on channel CH37 CH38 CH39 there is a strange current peak, witch I don't understand...
Hi,
I can't build any samples anymore for my nrf9160-DK using neither SES nor CLI only.
I followed the "Getting started assistant", pulled the v0.4.0 version of the SDK...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
