i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi, thank you for looking at my post.
I am using Keil V5.25.2.0 with a nRF51422. I am using the soft device "s310_nrf51422_1.0.0-2.alpha_softdevice." My memory regions for...
So, currently I utilize DK's to program and debug both pca10040 and pca10056 utilizing a custom shield that plugs into any of the nRF52 DKs. The programming and the debugging...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
I have the nRF51-DK and have installed Python etc. and the nrf_sniffer_2.0.0-beta-1_51296aa.
3 .hex files are in that installer: sniffer_pca10028_51296aa.hex, sniffer_pca10031_51296aa...
Hello,
I'm trying to shutdown my whole system (nRF 52832, SD132, SDK 12.3) after advertisement fast and slow are finished, following the structure of the peripheral BLE_APP_UART...
Hi,
I am trying to run lightswitch example in MDK.
Provisioner keep logging : 419, Unhandled Mesh Event: 4
Button 1 is in on state.
and LD5 is keep blinking.
these...
Hello. I'd migrated my application on SDK 15.1 from 14.2. The firmware of my product is always updating so I use NRF LOG module to debug it and see what is going on in every...
Hi to all,
recently i bought PCA10059 board, but i have problem in programming it. because i had some experience with NRF51 and NRFGO, at first when received the board i...
Dear Nordic,
I am using nRF52840 chip for BLE Advertising I want to encrypt this Advertising
I Read a CCM-AES encryption in BLE is it right way to this 31 bytes advertising...
