Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Dear,
I have nRF9160 DK, and I tried to control SW5 to debug/programme for nRF91 or nRF52.
I could programme for nRF91, but I couldnt do it for nRF52, for example, Im...
I've tried the light switch example and it works pretty well. I want to make all the devices with the same model, so how can I send message from client to client?
A general question about the radio CRC registers: The CRCPOLY register is 24 bits wide, which can be used to specify a 24-bit polynomial, suitable for calculation a 23 bit...
Hello Everyone,
I need to turn off the bluetooth advertising on certain event/interrupt and start advertising again on another event/interrupt.
I have gone through the...
Have a nice day! We are working on a project where goal is to build up mesh-network up to 50 nodes with high sum data rate to up 100kbps through the node. For this purposes...
Is there any release timeline for a Nordic Thingy based on the nRF52840? Does anybody know of an open-access beacon that incorporates the nRF52840? Thank you.
I'm trying to communicate with a single NeoPixel ( WS2812B) using the PWM module.
I've configured a sequence array with the compare values necessary to turn on the red and...
Hi everyone
I'm trying to get the status of button by using the bsp_event_callback_t, but my application crashes when I push on any button.
Test environment: Freertos...
Hi Team,
For the board having Linux Host having nRF52832 interfaced over UART, what are the maximum number of BLE devices can be connected?
As per my understanding it...
Hello, this is Kwonjoon Lee, beginner of BLE development.
I successfully installed pc-ble-driver (c/c++) in accordance with Git-Hub guide ( https://github.com/NordicSemiconductor...
Hello,
This is Jahnavi. I am having nrf52 DK development kit and with that development kits I am using light switch example to connect the boards as mesh network. How...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
Hello:
I have nRF9160 SIP custom board. The pins on custom board almost the same as nRF9160DK.
I can run lte_ble_gateway sample on nRF9160DK without problem:
But...
I followed nRF Connect SDK 0.3.99 to test nRF9160 LTE Sensor Gateway.
I successfully completed steps 1 thru 10 in the Testing section
It was successfully connected...
Hi all,
I am communicating with a sensor through UART using APP_UART on a custom board (nrf52840) through the nrf52 DK. I can send and receive commands to and from the sensor...
