i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I am looking to select a bluetooth chip for a new project, one of the criteria is access to free development tools.
I see that in the SDK GCC is supported.
But: how...
Hi
in the beacon kit user manual I read that in order to put the nRF loader on my iOS device, I need to compile the project in Xcode and transfer it to my iPhone.
How...
Hello,
Does the NRF IOT SDK have any support for the LWM2M application protocol or is there an implementation of LWM2M on the IPv6 Bluetooth Stack?
Imran
Hi All,
I want to implement a network which will consist of 64 sensors at different location sent to a central node . Can use the nrf51822 with ANT mesh protocol to implement...
I am trying to look at power consumption for very basic use cases to understand how often I need to go into SYSTEM OFF state. I have a development board and am measuring current...
Hi,
Is it possible to to switch between beacon mode and DFU mode (DfuTarg) without the need to press the button e.g.: by using DFU characteristic?
Is nRF51822 Beacon v1...
Hello Everyone!
I want to program nrf51822. I'm using open OCD 0.9. I created openocd.cfg file:
source [find interface/stlink-v2.cfg]
transport select hla_swd
set WORKAREASIZE...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I've downloaded S130 SoftDevice and found an example s130_demo_app which contains a project file for Keil v4, but when I am trying to open it in Keil V5 (that is the only...
Hello -
I'm not having any success using my PCA10024 as a dongle for MCP. Here is what I'm doing so far....
Remove PCA10024 jumper from P0.30-GND.
Connect PCA10024...
Greetings,
I am trying to minimize my BOM line items. Can C10 decoupling capacitor stated as 47nF/X5R on the reference design be replaced with 100nF/X5R without consequence...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi,
I modified the uart_example project for the pca10001 board of the nRF51822 evaluation kit to make it work with a UART TTL JPEG camera. So far, the camera can receive...
Hi,
There was a thread about using PAs (and not LNAs) with the nRF51 a while back with some good advice.
One question I still have: is there currently any way to support...
