Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
I'm currently working on getting LTE to work on our custom card, featuring an nRF9161 and an MFF2 eSIM (without PIN), but I can't seem to initialize our eSIM. I have...
Hi,
I know this issue has been addressed in other posts but none of the solutions tested worked for me. I tried the solution of this post : Intellisense stops working when...
hw: nRF9160-DK, v1.1.0
Using the McuBoot-Loader of NCS 2.5.1 and the NCS 2.6.1 zephyr dfu module seems to be not longer aligned with it.
A app using NCS 2.5.1 zephyr's...
We are developing Matter/Thread based Smart Lock product. One of the product requirements is that the product should be able to connect to a BLE mobile APP at all times i...
Hi,
The CPU temperature module is located in the network CPU in the case of nRF5340. I have read this thread : Zephyr API to read the nRF5340 die temperature - Nordic Q&A...
Hello,
we use nrf5340 with Connect SDK v2.0.0 and we have adopted rules for indicating the update process and the operation of the bootloader in the device. Therefore, I...
I am working with the Ebyte e83 Dev board and Also got the ARM-JTAG programmer.
I have been trying to follow the nrf connect for VS code series and seems to get stuck on...
Before I got a white screen after selecting a ble chip (52840 dongle in my case), I deleted my folders home/ (.config/nrfconnect .config/nrfconnect-bluetooth-low-energy, ...
I just migrated from MacBook Air with M1 processor to MacBook Pro with M3 processor. I installed VS Code and nRF Connect SDK v2.6.0 from scratch on my MacBook Pro. hough my...
Hi，
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Greetings team,
We are using the nRF Connect for Desktop v4.4.1 and Programmer tool has been updated to v4.3.0
Using this version the MCUBOOT settings are unable to turn...
Hello, I try to config vendor id and product id according to https://docs.nordicsemi.com/bundle/ncs-2.0.2/page/nrf/ug_matter_configuring_protocol.html .
1) When I change...
Good morning,
I work with the nRF52840DK board and the BC840E and I would need to make some changes to the SW of the "radio_test" application, but trying it out I find it...
Hi,
I am going to consider NRF52811-CAAA in a design. Can you please help with these questions:
1- What is the expected End of Life for NRF52811-CAAA chip?
2- If I have...
Hello,
We have a custom board for nRF52805. We have one LED connected to the GPIO. I wrote the FW for Blink LED every second.
I build the FW using the command " west build...
