hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
To the kind attention of Nordic support team,
Following PPI examples, I configured PPI so that an external interrupt (transition hi->low on a gpio pin) is triggering a...
Hi everyone,
I am new to the development and I am trying to connect my nRF52480 to my phone. When I open the desktop app for BLE connections, I cannot select the start scanning...
Hello,
I am trying to communicate with a BT832X module ( https://ro.mouser.com/datasheet/2/915/BlueNor_BT832X_datasheets-1518727.pdf ) using a PIC microcontroller ( http...
Hi,
I'm devlopping python (v3.9.6) software to flash nRF52832 using pynrfjprog (v10.17.3) package.
The soft is a loop trying to erase and flash. But while debugging...
Greetings Nordic Team,
I am trying to pass data from an application on a dk-nrf52840 to a nrf52840-dongle whose uart is connected to the uart on a microcontroller. Using...
Hello,
I am trying to interface nrf52840 with HMC5883L magnetometer sensor to read magnetic field x, y, z values.
When it comes to results, as far as i understood, values...
Hi,
I try to use nrf52840 dongle and pc-ble-driver-py to connect nrf5340 and get the data from it. The handle and uuid is obtained from nRF Connect for Desktop BLE and the...
Hello,
I am attempting to use the NRF twi manager based on the "twi master using nrf twi manager" example. I noticed that the example only reads and wrties a single byte...
I am having an issue with the BLE App Blinky example where I am receiving this error while trying to build using make on VSCode:
../../../../../../components/libraries...
Hello,
I created a sucessfull code for nRF5340-DK working with bluetooth, uart etc. I am using the Bluetooth NRF52 dongle
to test. When I upload the firmware to nRF-DK...
Dear community, I have multiple device chips I often re-use in multiple projects. So I wish to create a shared zephyr external library for re-use. What is the best way to...
Hi:
Example path:
C:\ncs\v2.1.1\zephyr\samples\subsys\nvs
Build Config:
nvs v2.1.1
" *** Booting Zephyr OS build v3.1.99-ncs1 *** "logs will not appear when running...
Hi
we are using nRF connect SDK 2.1.0 and also MCU boot.
Following the steps to generated the keys for signing the images.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi.
i am using 5340 + ncs 2.0.2. and gpiote nrfx drvier.
i used gpiote for count encoder
encoder clock speed is about 2.5k and input pint is 2 gpiote pin.
gpiote polarity...
