Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I have built and loaded the ble_app_cscs example, including the S140 Softdevice. I can connect with the Nordic_CSC peripheral, but rather than show Cycling speed characteristics...
Hi, I was creating a new project that uses interrupt. I start from TWI Examples and implement interrupt on it.
So when I implement the interrupt method, I got this error...
Hello,
I am wondering if anyone has any measurements of the LC3 SNR / Distortion measurments on the NRF5340.
I have tried with the Audio DK but beleve im just running...
Hello Nordic team!
We are using nrf52832 chip and soft device S332. System runs custom bootloader and main application.
We did not have any major problems with BLE...
Dear Nordic Team,
The founders Lukas Pilat and Robert Kopka have met your representatives at the Light & Building conference yesterday. They recommended us to get in touch...
It seems like VS Code debugging will reset debugger if you click to reset MCU. This somehow leads to it dropping RTT. It further releases the CPU while reconnecting and halts...
Hello Nordic Experts,
Recently, I am using the nRF52840 dongle to sniff the Scannable Directed event, but I found that the AUX_SCAN_REQ cannot be sniffed, but the SCAN_REQ...
I'm using the UDP sample from SDK 1.8.0 with the following modifications:
No PSM
No eDRX
Send 100 bytes every 15 seconds
This is on the nrf9160-DK board.
I suspect...
I'm using embedded rust for a project on the 9160. If i configure any of the AIN0-AIN7 pins with the SAADC, my sleep current is 850 uA. Default config is resistor bypass,...
Hi,
I want to use NRF_RADIO->SHORTS register in my standard BLE application.
I am using nRF5 SDK15.
When I write in to this register before enabling the Softdevic, it...
hi,We developed a Bluetooth product based on NRF52832, but the bandwidth test was not qualified. According to the requirements of FCC Part 15.247 regulations, the Bluetooth...
Hello,
I have a project that is based on the peripheral_uart example that receives start and stop commands from a periperal_central device via BLE to send ADC samples...
Based on the NRF52840DK, we want to do a USB CDC DFU upgrade function, but we don't want to use the BLE demo. You want to enter the duf mode by adding and modifying registers...
I am facing a problem. Two sensors are triggering with data_ready pins and a timer value is captured upon the event. But the value can be stored only in RAM if a context switch...
HI,
I am working on nrf52833 board, while working with flash in dts file i could see that write_block_size is 4 bytes. Is there any way to reduce that , i need it as 1 byte...
