I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I’m currently exploring peripheral support on the nRF54L15 and nRF54LM20A series controllers. I need to turn an LED on and off using the PWM component. The LED is connected...
We are developing a device based on the nRF5340 with an nPM1300 PMIC. The device has three power modes :
Active mode: most peripherals are enabled, and BLE communication...
I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn...
Hello
I am looking to use [as much as possible of] the full-speed USB bandwidth of 12 Mbps (or 1.5 MBps).
I have been able to use the USB MSC for my initial testing (with...
Hi All,
VS Code version 1.105.0
Mac Silicon, latest OS version installed : Tahoe 26.0.1
Since yesterday, my "nRF connect for VS Code" extension is stalled : the...
Hello, I came across the Location Services page for nRF Cloud and noticed that it supports multiple location technologies, which is quite promising. One line that stood out...
I recently started tooling with Zephyr for low power Bluetooth applications and i was trying to build with sysbuild mcuboot togheter with my nRF52832 without success. I see...
Hi,
I see that Nordic’s nRF Connect SDK now supports the Google Find Hub (Find My Device) SDK.
My question is would it be possible to build an asset tracking solution...
When we were configuring SDA in the visualized device tree, we forgot which button for SDA we should click (as shown in the red box in my picture). Now all the buttons for...
Using the matter weather station as a base on a thingy53 and SDK 3.1.0 which should use matter 1.4.2 if i open zap-gui and try and add a Control Bridge (0x0840) i get notification...
Hi,
1.Please troubleshoot the issue and identify the cause for no response when sending AT%HWVERSION using the merged_serial_lte_modem_v3.0.0.hex and mfw-pti_nrf91x1_2.3...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
Hello.
I'm trying to use a nrf52840 as a central device and connect to a gopro13. The connection works a certain number of times. But after a while (several days or maybe...
