Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
I am using the SAADC (AIN2) to get temperature values from a Pt1000, and I am experiencing sometimes strange behaviour after the offset calibration is done.I have quite...
I am working with the NRF5340 to develop a BLE audio streaming application using a PDM MEMs microphone.
I have played around with the NRF5340 Audio DK and got PDM audio...
Hi
So the central multilink example uses init_scan . connect_if_match = true ; Mine is false, because I want to manage the connection myself.
I'm filtering out 5 seconds...
I am trying to debug an application in VS Code for the nRF52840 DK in the nRF Connect SDK.
After starting debugging, I immediately get this error: "Exception has occurred...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hello sir/Madam,
i want to change the code that prints values(the values are from nrf_dm sample) to the serial terminal in nrf52840 dk using nrf connect in visual studio...
It is not possible to connect to the Peripherial using identity address steps to reproduce 1. connect to peripherial using random mac address 2. bond using random address...
I'm currently working with a BL5340PA module with the external antenna connector. we were wondering what was the RF switch isolation between the two antenna outputs. In other...
Hello,
I am currently working on a project using a custom board with nRF52840 + nRF21540 . I am trying to measure wireless performance using Direct Test Mode (DTM) , but...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
