I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello, I have a problem with the I2C peripheral on my nrf53840. I enable i2c driver on my project and read sensors on the bus. Everything is OK. Then when with Power management...
Hi Nordic,
I am working with the s140, sdk 15.3. My application is a central that should connect to a device that has several services. As soon as the connected event is...
Hello,
I am using nRF Connect for Desktop 3.7.1 with a nRF52840 USB dongle for testing purposes.
In the Bluetooth Low Energy 2.5.3 application I deselected the "Auto accept...
Hi,
I'm using Nrf52840 to connect to a Mobile via BLE.
I'm advertising to start connection, and after bonding, I can start advertising with whitelist in order to connect...
When adding this line to codes from an article here control reaches
Example used is ble_app_hrs_pca10056_s140 on nrfDK2 , sdk 17
==================added to advertising_init...
Hi,
I'm trying to use Thingy91 as a gateway for collecting data through BLE (from other thingy52s) and send it to Azure IoT Hub using LTE, but the current sample code only...
Archlinux
Visual Studio Code: Version: 1.58.0-insider
nRF Connect: v2021.9.98
I installed the "nRF Connect" extension in vscode, and went to look into a problem I was...
Hi,
I'm currently testing LPCOMP with one of our nRF5340DK boards.
The power consumption of the LPCOMP seems way too big (around 140µA) once enabled with this conf...
Dear Nordic Engineer
Our customer uses NRF52832 to develop a computer remote control pen. They are based on the keyboard example in the 15.3.0 SDK. Now they encounter some...
I have a working (hand-wired) prototype that connects to the internet without any problem.
Now I have made a PCB to replicate the same thing and loaded the same software...
Hi, I do have a PCA10040 board, I'm using the examples from Nordic. On the DFU example for SDK 12 I have pressed button 4 and RESET the board to active BOOT . I’m testing...
Hi,
S112/S113 is currently the only supported SoftDevice on nRF52805 and doesn't support Central (Only Peripheral). Is there a plan to enable S132, SoftDevice Central are...
Hi,
I have nRF52840 DK boards.
This is rather an informational question for my benefits.
In post: https://devzone.nordicsemi.com/f/nordic-q-a/9315/nrf52-802-15-4
...
Hi,
I’m developing a BLE joystick with nrf52832 with a PCA10040 board
To make the development simple I’m using 16 input Buttons and 2 analog inputs with 8 bits each. ...
Hi,
We have a product that is based on 2 SDKs : SDK 14 and SDK 15. SDK 15 covers nrf52840 builds and SDK 14 covers nrf52832 builds. I know this is not perfect setup but...
