Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
i am a beginner with nRF9160-DK and i was trying to open a Project. Then i got the following error:
Creating solution rgb_led.emProject C:/Users/tcheced/ncs/v1.6...
I am using nRF52832 with nRF52 SDK 17
My application consists of two timers running every 5 seconds and every 35 ms. After some very long time and only with a few units...
Hi Nordic,
I've been trying to run examples developed for the PCA10059 for several days now without success.
I changed the Preprocessor Definition from BOARD_PCA10056...
Hello,
I am trying to create a custom driver for an accelerometer I have sourced. I am using the nrf5340-dk.
The code was not able to compile as a result of the following...
Following function implementation is not following POSIX documentation specified at https://pubs.opengroup.org/onlinepubs/9699919799/functions/getaddrinfo.html, which says...
Hello Nordic Semi
I know that nrf52832 does not support SPH0645 Mic on I2S interface because of data width limitation in hardware for nrf52832.
I want to know that does...
Hello,
I'm using the mqtt_simple example with the following changes to add WebSockets Secure Support:
Also I set the Application MQTT topics, clientId, host, port...
Hi,
I have multiple devices that support Nordic DFU.
I want to update them using a Linux computer with a bluetooth dongle connected on it (and its not a Nordic Device...
Hi, There,
About the interrupt priority, can I understand it like this? "The two levels: NRF_MESH_IRQ_PRIORITY_LOWEST and NRF_MESH_IRQ_PRIORITY_THREAD have the same functions...
Hi Devzone,
I know that we can adjust "Advertising interval", "Tx power", "Tx payload" to do a power optimization when advertising. But I when I set " Advertising interval...
Hello,
I am trying to decrease the power consumption of my board (nRF52 DK) so that I can only see what's consumed in advertising beacon demo. When I measured the current...
Hi everyone,
I have a board based on thingy91. I have lis2dh and adxl372 sensors on it. They are both connected via SPI, and I've added this to my overlay file:
Also...
Hi,All:
I have finished continuous unmodulated carrier by SD fuctions as below.It is more efficent than DTM examples。But now,I don't know how to ctreat continuous modulated...
Hi,
I would to design a custom PCB with nRF52840 SOC.
I have two different power source:
1. 3V Lithium coin cell
2. 3.7V LiPO battery with charging circuitry
I will...
