Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
The initialized struct "nrf_fstorage_t" for use in nrf_fstorage_init( ) temporarily includes the application and bootloader (just for this test)
start address is 0x2'600...
Hi,
I have setup a provisionner with the sdk example that can provision devices. For that the provisioner scan unprovisioned devices and can start a provisioning process...
Hello,
I am trying to see how the signal strength for Zigbee and BLE changes when the distance between two nR5340 DK increases.
I used central_uart and peripheral_uart...
Although my Googling skills are not the best I have, so far, been unable to find any examples or driver documentation for the comparator peripheral of the nRF52840 for the...
I'm using the asset_tracker app on a custom board and have built 50 of the custom boards. All but one of them start the modem and listen to the LTE receiver for a full minute...
Hello, I followed getting starting guide, and got SDK and tools installed for nRF52-DK, I'm trying to open, build and run some examples. But when trying to open any example...
Hi.
I am using nRF52840 dongle and running saadc example on it.
To print the ADC data buffer "p_event->data.done.p_buffer" in PC, I am using USB_CDC. The size of SAMPLES_IN_BUFFER...
I have implemented the custom service and added custom characteristics following the tutorial series, now I can connect and see the characteristics and their values. I can...
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
