I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I am using the Thingy:91 PCB and I have disabled the nRF52 by cutting SB4 and soldering SB3. This makes me unable to log through UART. For this reason I implemented...
To the kind attention of Nordic support team,
I need to disable, enable gzll more times. When enabling it, code gets often stuck in my case as in figure: nrf_impala.c 442...
I have achieved Bluetooth connection between 1*ble_central<------>6*ble_peripheral.
But, ble_peripheral sometimes upload data at the same time, then sometimes lose data...
We're successfully using nrf_crypto_aead_crypt() with AES CCM, a 128-bit key, a 64-bit MAC, and the NRF_CRYPTO_ENCRYPT operator to encrypt some data and generate a MAC that...
HI, all,
I am trying to transfer my previous project from nrf51822 to nrf52840, and at very the beginning ,I can not make the UART/UARTE of nrf52840 work.
0, I have programmed...
Hi, everyone,
I am pretty new to nRF52 development. Right now, I have an issue with the SAADC trigger by RTC, which I follow this example . The issue that I have right now...
Hey all,
Here's another question. Many of the examples in the Nordic Connect SDK are rather large. Transferring them with MCUmgr at 115200 BAUD takes sometimes more than...
Hi
I am testing sending and receiving data between nRF51 dongle and peripheral by example of heart-rate-collector.
now I could find characteristics I need(write, read...
Hi all,
My application is as follows:
I have an android app which will send some data to a nRF DK. The data I want to send is in HEX characters between 0x00 to 0xFF. And...
Hello,
For nRF51822 and nRF52832, I'm using GPIOTE, PPI and timers to measure the duration that a pin, which is normally low, goes hi (typically 100-300 milliseconds). I...
The following questions are in regards to the instructions at nRF_Connect_SDK-modifying-a-sample-application .
In the Windows environment, I am transitioning from using...
Dear all,
I recently made a custom PCB using the aQFN73 package of the nRF52840 and, even though I respected the antenna constraints (but in 2 layers) I get no signal whatsoever...
Hi Devzone:
I am using P0.00 as SDA and P0.01 as SCL on nRF52833, And I got waveforms like below when I am doing I2C transactions:
the red waveform is SDA and the green...
Hello,
I slightly modified examples\multiprotocol\experimental\ble_zigbee_dynamic_color_light_bulb_thingy so that it can receive changes in the color temperature attribute...
currently i am doing my master Thesis in Bluetooth low Energy. I am searching for BLE Transceiver for Evaluation Purpose. I have a development board S32 from NXP and would...
