Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
I am using nrf52840 board. I hvae interfaced a gsm module(quectel m66).The problem is my device gets an APP_UART_FIFO_ERROR after every few sms commands.The maximum data i...
Hello everyone!
I have an issue about upgrading firmware over Bluetooth LE with a mandatory pairing of devices. I want only paired devices to have the ability to upgrade...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
Hello,
Our team has narrowed down a particularly interesting issue with the boot sequence / initialization of our BMD-341 chip, which itself runs the nRF52840 SoC. For context...
Hi , i am using the nRF52DK and i have a small problem with the pwm driver.
i basically would like that the frequency increases if i press a button or decreases if I press...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
It seems like the only way to disconnect the input buffer is using ANAEN, but I know this post says that ANAEN is fake. So I am wondering if there is a way to disconnect the...
I'm trying to upgrade our project from v3.1 -> v4.1 of the Mesh SDK. The BOOTLOADERADDR() macro was re-defined (apparently starting in v4.0?) to use two parameters for which...
Hi,
We would like to access the print outputs of the SEGGER_RTT_WriteString() function via a JLINK compact debugger using Python. The latter is wired only via SWDIO, SWDCLK...
Hi,
I want to integrate HID mouse and HID keyboard in a single device. Can you tell me the complete configuration procedure to integrate HID mouse and HID keyboard in a...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
I'm using the NRF8001 with a Teensy 4.0. I've been able to find a port of the Arduino library for the Teensy here ( https://github.com/tato123/nrf8001_arm_support )
I'm...
I saw on the main Q&A page the person answering the Q&A said " one should really put the application in one CPU (the M33) " which I understand the nRF 9160 is the M33 processor...
