Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
Hi
The flash data retention time for nRF52832 have been specified for 10 years @ 40°C. Is there any data available what the retention time would be at higher temperatures...
We are developing tracking system for our ground floor car parking but couldn't able to get GPS location.. we install Nordic Thingy:91 inside the steel body. Please let us...
Hello guys,
We are developing nRF52840-based device that needs to act as both BLE Central and Peripheral.
Peripheral role:
In BLE Peripheral mode, nRF52840 should advertise...
I have a need to send pressure data form 1 device to 4 other devices , it is medical application , data rate is in such a way to be in human readable form, can i use nrf24l01...
Hello, Just purchased a nordic NRF5340 PDK from digikey. On plugging the micro USB 2.0 and switching on the device , the device powers up for couple of seconds (LED1 & LED5...
I'm trying to add BLE_UART functionality to a custom board, on top of the already existing USB (and working) USB_CDC CLI. I'm using SDK 15.3.0 and softdevice S340
I used...
Hey
I would like know how can i add battery model for mesh. I have seen the Battery indicator in normal BLE sdk, now I want to implement in mesh sdk in the form of model...
I'm currently using a HostController with pregiven communication protocol for transfering data to the NRF52840 (over uart). The NRF is flashed with the SD140 and I'm using...
Hi Dev Zone Team,
I had a question regarding the current measurement of Nordic Thingy 91. I am following the steps provided in the Thingy91 documentation.
I have a Joulescope...
Hello.
I am testing saadc function.
When I was connect the saadc pin with ground level, the saadc value represents negative value.
So I am searching the similar problem...
