Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello!
I have created a function that cancels the connection by pressing and holding the button when Bluetooth is connected.
The use of this code allows the connection...
Hello,
I want to use FDS with bootloader but i get this error and i'am not sure how to manage it cleanly:
Linking target: _build/nrf52840_xxaa_s140.out
_build/nrf52840_xxaa_s140...
I have done a number of BLE projects using this chip. I am exploring two potential applications which would use the 2.4 GHz radio, transmit only, in a non-standard way. I...
Hello.
I've been asked to help develop an IoT device where GPS positioning and transmitting status via LTE-M/NB-IoT is central. So I've landed on the nRF9160 device, which...
I have a project bord which base on nrf9160, two buttons are set in the hardware circuit, corresponding to the pins of P26 and p15 respectively, and P07 is used as the interrupt...
It appears on the Thing91 reference board that the SIM_DET pin is used to drive the SIM mux control pin. Is that case? Is there more information on how to use this?
Is it acceptable to use the nrf52805's DEC4 pin as 1.3 V reference? I've connected the pin across a ~11 MOhm divider to to create a 0.12V reference for an op amp. I figured...
On SDK16.0.0 + Mesh SDK 4.1.0
I am using a Fanstel BT840X module that has an onboard Skyworks SKY66112 PA/LNA.
I followed the Infocenter guide along with an old example...
Hi, I'm having an apparent memory issue after increasing my PPI channel and GPIOTE allocation. Here's the basic setup:
nRF52840 with SoftDevice 6.1.0
SDK 15.3
I...
Hello,
We're intending to use the free flash region for two purposes: Flash Data Storage and DFU. The Flash Data Storage will be allocated a large number of pages (100...
I am using the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant parts to my app.
It is now apparently working. The...
Hello ,
currently i am working on indoor navigation project for that i was setup 4 node in a square shape, the nrf52832 beacon was continue transmitted packets. we also...
Hello,
I've been looking into the performance of the coded PHY (S8) to see if it fits the needs for a product we intend to make. All research and documentation I found about...
