I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Here is the code i am writing, yet leds dont blink-
#define LED1 BSP_LED_0 #define LED2 BSP_LED_1 #define LED3 BSP_LED_2 #define LED4 BSP_LED_3
int main(void){
bsp_board_init...
Hello,
I am evaluating what the best way is to solve this problem: We have 2 network interfaces on our board. We would like to be able to switch between them dynamically...
Hi, I'm a beginner in working with these Nordic Development Kits. I've been following the steps outlined on the Nordic website for getting started with a nRF52840 DK. It tells...
hi,
I have 2 PCA10056 and few PCA10059 for BLE mesh testing.
need to configure dongle as provisioner.
unable to configure mesh provisioner example(also other client...
Hi,
I am working on a project which will connect to device having static mac address . My job is to make sure that the device will connect to device having BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
Hello,
I wanted to replicate and build the LED Button Service using my own custom service. I used the template BLE project as a starting point.
I am using nRF52 DK, and...
for (int i = 0; i < LEDS_NUMBER; i++) { bsp_board_led_off(0); nrf_delay_ms(500); bsp_board_led_on(0);
}
in this code only the first command gets executed.
It turns off...
Hi,
We have several boards on hand which fall into two categories:
Category A: Our application has been programmed with JTAG in the past
Category B: Out application...
Hello!
I'm trying to DFU an NRF52 device on a custom board using nrfutil
I'm able to DFU the device using the NRF Connect v3.3.0 software together with an nrf52840...
Hello,
My problem statement is something like this:
Implement a Transmit Enable (TxEn) on a GPIO pin.
TxEn should be initialized low.
TxEn should be pulled...
I am new to Nordic and i am using nRF52840 DK, - SDK 15.2.0 - s140. I have written an application by modifying the Heart rate Monitor example. My program acquires and sends...
hi,
I am working with usb dfu bootloader for nrf52833. I set the bootloader entrance mode to GPREGRET only. before enter bootloader, I set NRF_POWER->GPREGRET = 0x00000001...
I downloaded SDK V17.0.0.9 and opened BLE_APP_UART example from /ble_peripheral folder on IAR EWARM. I choosed ble_app_uart_pca10040e_s112 and compiled without problems. ...
Our system is currently using the ble_radio_notificaiton components provided by nrf5_sdk version 16, and we have noticed that occasionally after ble pairing + bonding operations...
Hi
I use nRF52840 demo board load the firmware( C:\sdk\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\cli\ftd\uart\pca10056\blank\ses )
the putty can work...
