Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello, I am I'm a Beginner at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
I am developing using the example of 'ble_app_uart...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
Hello Nordic community,
I have a nrf52-DK with SDK15.2.0 and I'm trying to communicate with ST HTS221 sensor. I have the original STEVAL-MKI141V2 evaluation board.
I...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
I'm using nRF52832 with SDK v15.3 and S332 v7.0.1.
The Wireshark capture snippet shows our product connected to an iPhone using our proprietary service with a single notification...
I am using the nRF SDK v15.3.0 example project ble_app_rscs on a PCA10040 development board. I am trying to determine the functionality I need to port to my pre-production...
I would like to get timestamps with ms accuracy in order to compare it with power measurements taken simultaneously. The +CCLK command accuracy is in seconds and there are...
Hello, I am currently working on a nr52840 s140 Sdk 17.0 (dev kit) and a m using the peripheral/uart example code.
The UART TX & RX works perfectly when connecting to a...
Hi,
Quick questions regarding MAGPIO setup.
We are setting up MAGPIO pins via AT commands for RF switches.
Should the AT sentence for setting up MAGPIO be the same...
For a customer we're trying to see if we can build an IoT solution with nrf9160 to periodically send a status update to the cloud. Unfortunately, the devices are typically...
Hi everyone,
I suppose that this is a simple question but I cannot figure out what I am doing wrong. I am trying to set up an interrupt for a GPIO
I call the createInterrupt...
