I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I try to create an MQTT AGPS tracker.
I'm using a nrf9160dk with the 1.3.0v.
I use two threads, one for GPS (A-GPS) and one other to send value to MQTT (witch starts...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
To set the transmit power for advertisement, I am using sd_ble_gap_tx_power_set...
We are planing to use nrf52840 sdk in our project.we want to use mesh stack for that.
our product is sensor:
-deployed in oil field.
- send data 8 times a day.
-payload...
Hi,
I'm developing on nRF51422 board and I'm currently adding BLE security just work feature based on SDK12.3.0 using softdevice s130_2.0.1(nRF is used as BLE peripheral...
Hi
Past week (on a Windows 10 pc) I've installed the nrf connect sdk (nrfconnectsetup331ia32), and yesterday offered me an update (nrfconnectsetup340ia32); since I've not...
Hi, I encountered the problem of losing data in uart serial port when using ble_app_uart_pca10040_s132 example.
sdk 16.0.0, s132, 7.0.1, nrf52832,
APP_ADV_DURATION=0,...
I want to connect two nrf52840 device and raspberry pi. When connecting to a single device, it works fine. However, when connecting with two devices, an error occurs and stops...
Hello all,
I am interested in using the Secure Serial Bootloader to program my NRF52832 over UART from an external MCU. I am aware of the SDK example and creating DFU...
I have a system that will have multiple ways of doing DFU. BLE, as normal, UART under special circumstances, and a "no transport" way. In the latter I will have transported...
Hi guys,
I was working on my nRF5340 based custom board. From a certain point on the nRF5340 stopped to accept any command from J-Link (SWD link). For example, in response...
I Separate two projects ,SPM application and non-secure application.the spi driver can work in non-secure application,when I try to transplant the spi driver in SPM application...
Hi,
We are using nRF52840 in HV mode and VDD is configured for 1.8v. By mistake, we have connected VDDH to one of the GPIOs as input. What are the implications? How much...
Hi Team,
We are using nrf9160 DK, So we tested the lte_ble_gateway application where we can take the ble data to cloud acting 9160 as gateway. So we also want to perform...
Hi, I'm trying to get the gps driver to work, but the initialization requires getting a device binding. The Asset Tracker project does it like this:
device_get_binding(CONFIG_GPS_DEV_NAME...
<environment> - Windows10 - nrf v1.3.0 - modem v1.2.0 - DK 0.9.0
I get "CLOUD_EVT_ERROR" when using nrf_cloud_agps. There is an error saying "Connection was closed, possibly...
