Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I want to use the REAL GPS of the RF9160, not the simulated version in the asset tracker demo. Firstly, is there a demo for the RF9160 that reports actual GPS location that...
When I'm running a BLE application with the debugger, and the CPU halts on a breakpoint, it seems to end up in the assert handler when I start it again. How can I avoid that...
We are working on a nRF91-based device, and trying to understand the regulatory premises.
From what I can see the module is approved according to GCF (www.globalcertifications...
Hi,
I have got new nRF52832 custom board. I am able to send AT commands and getting responses. After that i tired programming ble_app_uart Example and it stuck at ble_init_stack...
I take the TWI master example of nordic, and try to build I2C read API that can be use from otherr places.
The function look like this
uint32_t Serial_read_2BytesReg(uint8_t...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
Since writing to the softdevice...
I am a bit confusing about this two mode settings. We plan to use MODE=BLE_2MBit on both TX and RX sides as it can give us about 2dBm sensitivity improvement on the RX side...
I need to transfer data from my ADC (analog to digital conv) on a custom made, nrf52 PCB to a mobile app via bluetooth. For this I integrated my working SPI data transfer...
/** * Copyright (c) 2014 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are...
Hi there:
I'm now developing a product with 51822 using the SDK10.0 . The product communicate with another chip through UART.
My problem is when the UART crash with error...
Hi all,
I have an application where I have a mobile app that communicate with up to 20 BLE devices. The BLE devices are RGB LED lights with push buttons and a sensor. I...
Hi.
I'm trying to use nRF52 as TWI slave.
I am using Segger Embedded studio for the coding part and nRF52840 PDK.
I wanted to use TWI between the nRF52840 board and...
Hello Helper,
I am currently running ble_app_uart on 2-3 nRF52 dongles that acts as a node and ble_app_uart_c on nRF-52 DK that acts as a central. While establishing different...
hi:
App <lightblue or nrf connect> (ipone6) connect nrf52832 failed .But using Android won't cause this problem.
Here is the log that failed to connect lightblue...
Hello,
I am using my own board with the NRF52832 device.
I currently have a NRF DFU bootloader programmed and soft device. I used it to download my own App using the NRF...
