Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I programmed a PCA10001 with the HID Keyboard example and changed the preprocessor code from NRF6310 to PCA10001. The functions were tested according to the online HID Keyboard...
In the main function, this works.
Works ..
Not works , I got NRF_DRV_TWI_EVT_DATA_NACK error..
and I cannot call "nrf_drv_twi_tx" in the timer event handler...
Hi everyone, I am testing out the qspi flash on pca10056. While the read speed is decent around 650 KBs, the write speed is too slow ~ 35 KBs. It could be our own usb/caching...
There is an example in the SDK v15 folder. " ble_app_buttonless_dfu "
I write a custom firmware which has ble interface sending temperature data.
I want to add ble bootloader...
Hi,
I'm using the S132 v6.0 and SDK v15.0 to work with nRF52832. I found the it just get the advertising data. If the device put some data into the scan response, when I...
Hi,
I want to use nRF52840 USB dongle in my setup with other PCA10056 boards. I have seen that in link https://www.nordicsemi.com/eng/Products/nRF52840-Dongle it is mentioned...
Need to upgrade bootloader by application code. I have finished to program bootloader image to FLASH. Content is verified correct, comparing to SRC. However, the bootloader...
I have 2 52840 modules with PCB antenna and I am trying to check the max connection range
I followed the recommendations and achieved only 120m.
I cannot use the examples...
Hi, we recently using audio with ATVV service instead of HID service. As we notice, Audio would enable by SR3 itself in ATVV service if we push the key, but not in HID service...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
Hi guys,
I am using the softdevice S120 firmware: s120_nrf51822_1.0.0-1.alpha_softdevice.hex
The error_handler registered when calling sd_softdevice_enable is called...
We are implementing a Nordic NFR52832 using the ARM mbed ble stack that leverages the Nordic SDK using a HID over GATT profile. Windows 10 seems to have an issue with this...
Hi all.
I'm trying to make a list of brands and models of Android phones that have implemented LESC. I appreciate any feedback and experiences working with LESC (numeric...
Hi There,
I just want to confirm which method is being used to perform DFU over thread (Single bank update or dual bank update), and can I perform DFU on Sleepy end device...
