Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I followed the MacOS command line installation instructions at docs.nordicsemi.com/.../install_ncs.html
After running `west update`, it says the tree structure should be...
When following instructions for setting up the NRF52840-dongle as RCP coprocessor , I'm getting this error: ModuleNotFoundError: No module named 'intelhex'
Full log...
I have some initial questions regarding the nPM1300 :) :
- It is possible to download the nPM1300 datasheet as a PDF file instead of viewing it online?
- Regarding VBUS...
When I do a sd_ble_gattc_char_value_by_uuid_read I can only get a maximum of 253 bytes.
And when I read more I get a gatt_status of
BLE_GATT_STATUS_ATTERR_INVALID 0x0100...
when testing NIDD on NRF9151 we are using sock connect -f packet -t raw but it is giving us error
mosh:~$ > sock connect -f packet -t raw sock connect -f packet -t raw Socket...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
Hello, and thanks for reading. We are having some problems with our device, and hope someone here has the missing piece of wisdom we need. Our device implements HID over GATT...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...
Hi,
My custom board uses Raytac MDBT53v, which has nRF5340 as its MCU.
My SW is based on the example audio code, and I want to use my external NOR FLAH IC (Macronix MX25R6435F...
Hello,
I am finishing the development of a device based on the nrf52810. When the device is connected to a central, I would like to periodically measure the voltage on VDD...
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
Hi everyone,
I'm currently working on a project involving an Ember ZigBee end device and a Nordic ZigBee coordinator ( Nordic nRF52840 donngle) . I’ve encountered an issue...
I am not being able to set up the modem in Pakistan. We bought the board in Canada and we've tested it out in Canada without any issues. But the same Soracom sim card is not...
Hi,
I am writing a app.overwrite to remap my pins table. I can use
/delete-node/
The above is no problem. Bu my pio is overlay with gpio1 pin 5. The original dts...
