hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
For some reason, all of the VSCode action disappears after building the application with mcuboot using sysbuild on ncs 2.7.0. The application can only be built using...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
Hello
I am using nrf5340 raytak board which does not use DC_DC power, uses internal quartz. When I play the Bluetooth peripheral example I get the following error(I using...
I'm trying to build a simple water leak detection system. The sensor would need to alert a user through SMS/mobile notification when a leak is detected.
I was thinking of...
hi, I am working on to combine USBD CLI and RTT to USB HID with SDK 17.10, configuration as below
pls see below mainloop:
other codes are based on example of USBD...
This is driving me totally nuts. There are inconsistent pieces of information in documents and code. I am getting a modem reset loop problem. The documentation says the timer...
Hi,
Long story short, I made some boards using nrf9160 modules, received parts from DigiKey, soldered but can't make them work, at all.
nReset pin is stuck low. Tried...
I am using nRF52832 for high-rate sensor.
Of course, I can use SPI using CPU but it's busy for other jobs.
So I want to use DMA if it's possible.
Currently I am using...
I am using the nRF5340 and trying to get MCUBoot working. I am running into problems and looks like I need to edit the MCUBoot code, the problems are long and numerous too...
Hello everyone,
I'm using the Bluetooth Peripheral sample UART and have noticed an issue.
When I perform a lot of sequential pairing requests followed by cancels from...
