Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am facing issue with nrf5340 DK. It is not powering ON properly and not detecting.
When I am trying to power on the DK by connecting USB, the LED5 (PCA10095) on...
I'm trying to get some data written and read from flash memory using the fstorage library as explained in the examples provided with the sdk.
I write to flash and get the...
Hi,
I am still investigating this but, I think it is best that we discuss it on this forum.
I am using SDK 16.0.0, nRF52840, secure_bootloader_usb on a custom board. The...
I just received notification from Onsemi that the ESD protection chip (CM1402-03CP) that I am using between my SIM card connector and nRF91 is obsolete. This is the same chip...
After upgrading nRF Connect SDK to v2.1.0 I noticed that my modified version of connectivity bridge (when running on thingy:91 nrf52840), stops working 30-60 seconds after...
Hi I'm developing a board to isolate external GPIO signals from a Nordic nRF52832 (Isolated input from 5VDC to 25VDC). For this I am using a circuit with the PC817 optoisolator...
Hi, I have similar error on this thread:
I cloned current latest releases of Android-nRF-Toolbox(3.1.3), Android ble library(2.5.1), and Android common library(1.0.27...
Hi everyone,
I'm using an nRF 5340-DK and want to update the application core firmware by using the nRF secure immutable bootloader. The bootloader and the network core...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
