Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
1. I would like to know which rexample should be used when using nRF52820 as master and slave?
2. How many slave can be connected at most?
Thank you for all your...
Hi, Working with nRF5340 in NCS 1.9.2, I've overridden weak usb_update_sn_string_descriptor function to set iSerialNumber at runtime. I wanted to read the actual serial number...
Hi, I am currently working on moving our app over to PSM mode.
We have earlier used manually disabling and reenabling the modem when sleeping, using LTE and getting GPS...
hi, I am trying to use Hal_Atomic_Start() and Hal_Atomic_Stop() to imply an atomic block, in order to avoid interrupt from system when execute the atomic block, source code...
Hi,
The nRF UART running over the ASYNC interface consumes a lot of current even when not in use. As ours is a battery-operated device we intended to disable UART when not...
hi
im working with a custom project which can flash easily on a eval board im trying to add dfu for my project but it didnt work hence i added my project into the buttonless...
Background:
In pursuing development of Thread-enabled devices for use in home automation, especially using the just announced Matter 1.0 protocol, the nRF52840 Dongle is...
Hello,
in my device tree there are three nodes/items concerning battery Management:
One load enable pin
One measure enable pin
the required ADC configuration
...
Hi Team,
We are currently using nrf Connect SDK 1.8.0 and developing our application using nrf52833.
Currently we use our own git to maintain our application and nRF...
Hello, When enabling the Sensor system and having a qdec device enabled in my dts I get the following error:
This seems to be a bug with the Zephyr code checking a const...
Hi,I'm using nrf52832. I configured P0.20 as GPIO output,P0.22 as GPIO input.These two pins are connected wiht a 10Kohm resistor.I measured the voltage level on P0.22 is about...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example.
I'm following this guide https://infocenter.nordicsemi.com/index...
Hi,
I am working on thingy91, I have created/added a BMS module in the project which gives different values for different data fields.
Everything is fine as BMS is transmitting...
Hi,
I am using TWI channel0 on my nRF52833 as master to get readings from a few sensors.
I need my nRF52833 to communicate with another microcontroller over TWI/I2C so...
I have code which works on the nRF52DK and on the Fanstel BT832 module, which does not work on our custom board with the CIAA package. Our custom board does not have an external...
