Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Dear Nordic Engineers
If we use the NFC Tag of nRF52 series chip.A re there any card readers on the market that can read or write?
Such as ， NXP's NFC tag chip can be...
Hi Nordic,
I am using nRf52833-DK with zephry, an now I'm tring to drive ws2812 led strip.
I notice that there is no nRf52833-DK example in zephyr/samples/drivers/led_ws2812...
Hello,
At the following URL,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support.html
In "The Thread and Zigbee protocols support...
Good Morning people. I'm developing a module with the soic nrf52832 and I'm having doubts about the electrical schematic of the UART communication with another MCU. I analyzed...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
Trying out Nrf5 sdk v17.1 with SES 6.32 and opened up an ANT+ example `ant\ant_debug\d52\s212\ses`
Tried to build, 50% compiled successfully, but i get repeated errors on...
We use nrf52833, and the SDK is 17.1.0. We have the following questions about gzll: 1. How to count packets_num and timeouts_num in Packets Statistics? timeouts_num Where...
