hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
Hi,
My customer occur a problem with nRF5 SDK10.0.0, the sample ble_app_hids_keyboard.
We test the sample on nRF51DK.
We connect the DK with an Android phone, and bonded...
Hello, I downloaded the NRF5 SDK for mesh. I want to make the light switch example. I installed the server and client software on two different cards. I want to make the necessary...
I am using NRF9160 (PCA10090, 1.0.0, 2021.7) for my experiment using the .hex file of UDP example provided here ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hi
I use the nRF52840 board and am currently working on a Matter project.
I am trying to add a cluster to an existing Matter sample project as per the link guide below...
Hi,
I am working on pdm mic integration in zephyr RTOS. I used INMP441 mic sensor. I got SPL in dB by using nrfx. I want to create a driver for this mic. Please help me...
I have an nrf21540-ek. I hope it can be used with my nrf5340-dk. Does NCS 2.0.0 contain relevant drivers or does the driver need to be implemented by me? If NCS 2.0 contains...
Hi, recently I am been consistently getting the same issue as this post, despite having successful performed the Mesh DFU in the past and with the example code:
I suspect...
