I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi there, I-m trying to compile a hello world sample with an encrypted bootloader
# Sysbuild configuration file.
#see C:\D\dev\nordicsemi\v2.7.0\nrf\doc\nrf\releases_and_maturity...
Hi all,
I'm currently facing the issue that we are receiving a PKCS7 encoded response from our EST server via a `/simpleenroll` request.
The PKCS7 response now has to...
We have a locator-beacon setup based on this https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth/direction_finding_connectionless_tx/README.html running...
I have been facing a persistent Zephyr CMake/Kconfig build failure in my nRF Connect SDK setup.
Environment: Windows, nRF Connect SDK v2.7.0 , Toolchain v2.7.0 , using VS...
Hello Nordic team,
we are using a nRF52820 module in a beacon. After flashing the firmware and connecting via nRF Connect for Mobile, we can read the Service and Characteristic...
Hi,
I'm trying to CONFIG_MCUBOOT_ACTION_HOOKS with mcuboot on a custom board build with an nRF9151. McuBoot works well, but I'd like to use CONFIG_MCUBOOT_ACTION_HOOKS to...
Hi
I use MT8852BE to test nRF54L15-DK ,TX power setting 8dBm but MT8852BE Power(Pavg) show -6.07dBm ,Why is there such a discrepancy in the values?
nRF54L15-DK Setting...
For power cost down, use dts config to set pwm gpio H0D1 as follow:
pwm1_default: pwm1_default { group1 { psels = <NRF_PSEL(PWM_OUT1, 0, 26)>; nordic,drive-mode = <NRF_DRIVE_H0D1...
Hi,
We have defined a FOTA update for a set of devices. Our device SW follows the 'multi-service sample' code for FOTA.
Generally, FOTA works well for devices in a job...
Currently (as far as i can tell) the firmware for the DECT-NR+ mode is mutually exclusive with the LTE firmware, and you cannot mix the two wireless modes as you have to flash...
We use the device shadow "desired" section to send configuration params to the device. The device processes and accepts the params and then returns them in the "reported"...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
