hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
Hi,
we are developing a system based on device with nRF52840 S140 ( central and pheripheral).
We developed on both side a custom service.
System is working fine bonding...
I'm new to the Bluetooth mesh world and I'm trying to change some basic configuration parameters during runtime, by modifying the Light Switch example. I've searched around...
Hello,
We are using Zephyr v2.6 and nRF51822 SoC in our project.
Because we are porting the code from the SDK environment into the Zephyr environment, we decided to use...
Hello everyone,
in the last chapter of
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-4...
Hi,
I have removed UART from my custom board dts file as in my current application, I am not using UART for any transfer.
But due to this, I am unable to compile code...
Dear Forum,
I already succeeded in using the Nordic Toolbox's DFU-App to update the firmware of a BM833 via secure bootloader. I found out, that the Android DFU App is available...
Greetings,
Which Bluetooth LE examples in NCS v1.9.1 are suitable for the nRF52810?
I tried the usual suspects. peripheral_uart overflows flash and RAM.
peripheral_lbs...
The documents for setting up and using a Matter network require a change to account for new behavior of the chip tools.
https://developer.nordicsemi.com/nRF_Connect_SDK...
