hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I wrote a simple terminal that reads the keyboard input from USB UART device and echos it back to the same device. It works as follows: 1. It registers an interrupt handler...
Working application, using S132 SoftDevice, new variation of the application. Using UARTE, with P0.12 assigned as RxD. Something in the SoftDevice is grabbing P0.12 and setting...
Hey, I was trying to look for information on how nrf9160 modem selects the network to use, since we are having slight trouble with some devices triggering full network re...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hi all,
I'm working with building/programming v3.1.1 SLM application for my nRF-9151, it all goes well while testing with nRF-9151DK.
But when I want to try my custom...
Dear Nordic Team and Distributors,
For nRF54L15 (CSP and QFN) design circuits, how to optimize the stable modulation issue?
What aspects should we consider to do failure...
Hello Nordic team,
We are evaluating nRF54L10 for a battery-powered Bluetooth LE medical device .
We are considering the nRF Connect SDK Bare Metal option instead of Zephyr...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
Greetings,
I'm considering nRF52840 for a product. My connectivity requirements are BLE 5+ (For GATT-based communication, No requirement for channel sounding, etc), USB...
Hi,
working on custom bootloader on nRF52840 with S140 v7.2.0(not enabled in bootloader) with SDK.
This is code for erase and write:
Now, when writing I get prints...
Hi there! I am trying to set up external flash (w25q64) with my NRF52840 project over SPI. I have adapted the spi_flash sample in an attempt to set up this device, but I am...
Hi,
nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue?
Test Results
Test 1 — Out of Faraday cage, internal...
Hi everyone,
We recently started to add the iBeacon broadcasting to our own BLE project that runs on an nRF5340. It is based on the code from the sample of the SDK (we currently...
Saw this post from about 1 year ago.
Any updates regarding USB host firmware support on the nRF54LM20 or any timeline for when it is expected to gain some level of support...
