hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
I recently updated to nRF Connect SDK v1.8.0 from v1.5.0 and am encountering a new error with the same code. The error occurs when I call bt_le_ext_adv_set_data. My advertising...
This is in regards to my last post here: https://devzone.nordicsemi.com/f/nordic-q-a/84016/switching-between-two-applications-using-nrf5-sdk
I am using FreeRTOS.
Both...
During the development process, I had no trouble bonding with the rfConnect (current version from the website). After many changes to code, I got it to bond one time and deleted...
Hi,
Is it possible to use "nearby fast pair" technology on the nRF52833 platform? are there any examples of the use of this technology?
Best regards,
KaEd1705
Hi, I am using libuartes and when I receive text from other device my nrf52833 will respone "textAT1_Uart1". But I can not free them (using &libuartes1 because I'm using 2...
In nordic ncs zephyr use Nordi ble controller (SDC) else in zephyr mainline will use a software version of the controller that use LLL (BLE CONTROLLER).
Il possible to know...
I'm trying to create a minimal executable that has a structure placed at a specific address in flash. It looks like CONFIG_CODE_DATA_RELOCATION is needed to do this. However...
Hello,
we are trying to get the uart secure bootloader running on the nRF52820. When linking we receive the error message that RTC1_IRQHandler is defined multiple times...
For an upcoming product based on the nRF52811 chipset I wanted to prepare for the arrival of the new AP-Protect variant of that chipset and have a unified firmware that runs...
I'm using SDK12 and SDK15 on nRF52832 and nRF52840 (peripheral and central), although this would appear to be an issue with other devices too.
If I connect with NRF Connect...
Potentially related to : nRF Connect v3.9.3 does not detect external j Link programmer - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) , but I don't see the...
Hi,there:
I was used 2 52832 board to run the linght switch server/client examples to test message communication. I add the mesh events handle like this:
Then run the...
Hi,
I am trying to transfer a dataset of over 100k, via a custom service from a peripheral device.
There are many posts in this forum that describe ways to do this but...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. The Client sends unacknowledged messages to the Server ( APP_UNACK_MSG_REPEAT_COUNT...
Hi,
We are facing some issues with the DLE update.
The given table shows that the softdevice set data length and time.
Event Length (ms)
ATT MTU (bytes)
Data...
