hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi
I am having some issues with running QSPI on the nRF5340DK board. After I disabled the QSPI, I found the board still having a high current consumption of 700 uA.
Although...
Hello,
We use SEGGER_RTT_ReadNoLock() in our code, and this works perfectly. Our nRF is connected to a DK, which is connected to a computer.
However, when we compile with...
Good Saturday evening,
Up until now I’ve been accessing the registers directly in my Nano 33 BLEs to experiment with Timers, GPIOTE and PPI, all via the Arduino development...
Hello,
We're building zigbee devices around the nRF5340 with the nRF SDK/zboss/zephyr. I'm working on custom boards and have based my 802154 code around the samples in nrf...
is there a way to get more control over the auto ack feature of the 802.15.4 driver in zephyr?
I would like to ack frames without destination address only if nrf_802154_ack_data_pending_bit_should_be_set...
Hi all:
I have a software version that allows Bluetooth to be connected to the phone normally,
When I tried to use the SPI interface, it happened as long as I used
...
Hi there,
I'm trying to wire up a Uarte client to a Uarte server where the client device is an nRF9160DK, and the server is an nRF52840DK.
Connectivity between the cilent...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
Working on a zephyr/zigbee/802.15.4 system and my code (loosely based on the Nordic samples) on a custom device was not behaving as expected.
So I broke out an nRF5340 DK...
Hello Devzone,
I'm writing to ask about how long a device running Nordic's aws_iot sample app (sdk-nrf 1.6.1 based, Zephyr 2.6.0 based) may be in a "radio idle" state, and...
